AeroFlash BASIC FLARM
One CanopyFlasher. One FuselageFlasher. One PowerBox PRO FLARM.
An all-in-one, cost-effective Flarm-connectable AeroFlash kit.
Stand-alone, canopy mounted forward-facing flasher
Six extremely bright red CREE™ LEDs built into an elegant, low profile Space Grey (Nextel like) enclosure, mounted in the front of the canopy. CanopyFlasher is made from a high strength, UV resistant ABS based polymer. Out of sight for you, but not for others:
The heart of the CanopyFlasher is the array of 6 extremely bright CREE LED’s emitting approximately 4000-4500 lumens, with powerful, oval lenses; two beams orientated vertically, and 4 beams orientated horizontally. This makes the Flasher well visible at distances of even up to 3500m, ±30 degrees above and below- and up to ±45 degrees left and right of the nose.
Safe to install
The CanopyFlasher system incorporated many safety features, like heat sinks, a temperature sensor to prevent overheat conditions and two status LED’s for indication of the operating mode and warnings.
CanopyFlasher is suitable for almost every glider, with canopies opening vertically and sideways.
Elegant and aerodynamic fuselage mounted strobe. 360º. Tiny.
Measuring at 110mm long, 15mm wide and only 11mm high, the AeroFlash FuselageFlasher is extremely elegant and streamlined, made out of a super clear UV-resistant epoxy. Its small size does not say much about its ability: with 16, yes sixteen extremely bright red or white CREE™ LEDs (±7500-8500 Lumen!), the strobe is very well visible at distances up to 3km.
Mount it on top of the fuselage, on the bottom. Only one small hole of 4mm is required for the cable. Mount it on a wheel door, or on an engine bay door for the least amount impact on the airframe, and maximum visibility.
PowerBox PRO FLARM
PowerBox PRO FLARM is fully stand-alone. It powers the CanopyFlasher, one FuselageFlasher and provides synchronised flashing sequencing logic. This PowerBox PRO is connectable to Flarm and features AUTO- and Hazard-mode logic.
PowerBox PRO FLARM continuously monitors the temperature of the CanopyFlasher system. If an overheat situation is present, it automatically shuts down the system to prevent damage to the system and to your expensive canopy. After a short cooling the system will restart automatically if conditions permit. Don’t worry, the system generally doesn’t get very warm in flight, but in summer conditions on ground without air flow your glider is well protected.
PowerBox PRO FLARM features one IGC-compatible RJ12 port for connection with a Flarm. PowerBox PRO FLARM can also easily be updated using a mini-USB port and our AeroFlash software. A DB9 connector is installed for easy connection with our CanopyFlasher system.
On the other side, a neat removable screw-terminal system allows a quick connection of the power wires and FuselageFlasher, and easy removal when needed. No need for soldering; everything is plug-and-fly.
PowerBox PRO FLARM is compact and lightweight: it measures 100 x 63 x 31mm (including mounting flanges) and weighs only 190 grams.
Due to PowerBox PRO FLARM’s synchronised flashing logic, power consumption is very reasonable and should not be an obstacle to installing AeroFlash.
Red or white LEDs? Your choice…
Let’s explain the pros and cons:
+ Better visibility of a white glider against a grey/white background. This is the most dangerous situation. Red clearly stands out.
+ Red means danger.
– Slightly less brightness than white LEDs.
+ Slightly better brightness compared to red LEDs.
+ Better visibility against a brown/green background.
– Reduced visibility of a white glider against a grey/white background (in clouds, haziness, snowy terrain, etc).
We recommend RED. This gives the best result in the most dangerous situations, where it would be very difficult to be seen otherwise.
Scope of Delivery
Complete as you’d expect.
1x PowerBox PRO FLARM device.
1x FuselageFlasher (Red or White LEDs) with 4m cable.
1x CanopyFlasher with 3M double sided adhesive foam tape pre-applied and 100cm cable set.
1x PowerBox PRO FLARM cable set with OFF/AUTO/ON switch with marking/label.
1x RJ12 splitter.
1x 3M Dual Lock adhesive tape for mounting of PowerBox.
1x Vinyl template for aligning the CanopyFlasher during installation.
Simply connect it to your power supply.
Scope of delivery. Cable set shown is a generic “vertical opening canopy” style cable set.
CanopyFlasher designed for your specific glider. Cable set shown is a typical “vertical opening canopy” style cable set, standard length 100cm.
FuselageFlasher with 4m wiring pre-attached
PowerBox PRO FLARM with DB9 connector and IGC-RJ12 port.
100cm PowerBox PRO FLARM cable set with OFF/AUTO/ON switch and pre-attached power connector.
OFF/AUTO/ON switch with label
Flarm Splitter 4-WAY
Canopy opening directions – different cable harnesses
Vertical opening – universal
Vertically opening canopies need an easy to attach, but most importantly, easy to DETACH connector. When jettisoning the canopy in case of an emergency, our connectors are designed to easily separate.
The AeroFLASH installation consists of commonly seen male and female DB9 (D SUB 9) type connectors for the data cables (status LEDs and temperature sensor), and for the power supply of the CanopyFlasher. It is sturdy, easy to attach, separate (locking screws removed), and highly suited for the currents.
The Flasher cable length is 100cm, suitable for every installation. Included as well is a 100cm extension cable.
CanopyFlasher with DB9 connector.
Easy connect, solderless screw-terminal system.
PanelContact for Grob gliders.
CanopyConnector for Grob gliders, to be mounted on the canopy frame.
Side opening – universal
Each glider type requires a specially designed connector solution. This is unique to every different glider type. A brief installation instruction manual together with installation example pictures will be delivered together with these orders.
On the side are a few examples suitable for Grob G102 Club/Standard Astir and G103 Twin Astir gliders.
If your glider is not yet supported, please contact us to develop a solution together.
Side opening – Schempp-Hirth type
For Schempp-Hirth panels we designed a special 7-pin spring loaded connector to be mounted on the glareshield/instrument panel cover and the canopy edge, which requires absolutely no force to separate. The connectors have two alignment pins, to avoid mis-alignments causing short circuits. There is no need to solder any wiring, however you will need to install the connector in a suitable location and drill some holes in the instrument panel cover. We include a mounting position and drilling template to make this a little easier. Also included are a few mounting support plates with various angles for optimal installation in your specific glider. Schempp-Hirth glider owners may also choose a panel mounted DB9 connector option if they have a lot of play in the instrument panel cover, as this should be fairly sturdy. Please refer to the installation manual for more details, or contact us.
Schempp-Hirth 7-pin CanopyConnector and PanelContact.
PanelContact connects to the PowerBox DB9 connector. Easy and safe to remove the instrument panel cover for maintenance.